All articles

November 16, 2026

What Is Antiblock Masterbatch, and Why Does Film Stick Without It?

The blown film plant was supplying clear polyethylene bags to a packaged bread manufacturer. The customer asked for more gloss and more clarity so the product would stand out on the shelf, and the plant removed the antiblock concentrate from the formula, because its particles reduced clarity. The film came out crystal clear and the sample was approved within a week. The first shipment arrived in the middle of the hot season, after several days in an unventilated warehouse. On the packer's line, the air from the blower could barely separate the faces of each bag, the machine lost cycles and the operators ended up opening bags by hand. Several rolls tore as they were unwound, because their layers had adhered to one another. The packer stopped the line for two shifts and returned the entire lot.

Antiblock masterbatch is a mineral concentrate that keeps film from sticking. It creates a microscopic roughness that holds air between the faces, and its dose is balanced against the clarity you need.

Why two layers of film end up stuck together

In the flexible packaging industry, this phenomenon is called blocking: two layers of film that have been in contact adhere to each other and require force to separate. It appears between the inner faces of a bag, between the wraps of a roll and between the bags in a stacked bundle. Its origin lies in the surface of the material and in the conditions the film goes through after it leaves the machine.

Smooth surfaces that push out the air between the faces

Low-density polyethylene, linear polyethylene and ethylene vinyl acetate copolymers produce very smooth, flexible films. When two of those surfaces are pressed together, they conform to each other across their entire area, push out the air that separated them and remain bonded by intermolecular attraction forces. The low molecular weight fractions that surface on the film act as a light adhesive and strengthen the bond.

Heat, winding tension and storage time

Process and warehouse conditions multiply the effect. A film that is wound while still warm reaches the roll with a soft surface. High winding tension compresses the inner layers of the roll with constant pressure for weeks. A hot warehouse softens the polymer, and the weight of stacked pallets presses on the bundles of bags. Corona treatment, which prepares the printing face, raises the surface energy of the film and also increases its tendency to stick.

The collapsed bubble and the inner faces of the bag

In blown film, the bubble is collapsed between the nip rollers and its two inner faces are pressed together while the material is still hot. Those faces later form the inside of the bag. If they adhere, the bag comes out closed and the packer has to open it at a pace its automatic line can no longer sustain.

What film that sticks costs your plant

Blocking is discovered far from the extruder. The film passes the outgoing inspection and the failure shows up on your customer's machine, days or weeks later, when the entire lot shares the same formula and the same warehouse history.

First, the customer's machine stops: the closed bag holds up the automatic packer, and the adhered roll tears or stretches and loses its print registration. Then comes the claim, with the lot on hold, the return freight and the replacement charged to the supplier. Antiblock acts on the cause, from the formula.

What antiblock masterbatch is and how it separates the layers

Antiblock masterbatch is a concentrate of fine mineral particles dispersed in a carrier resin compatible with your base material. It is dosed at the hopper and the particles are distributed throughout the film. Some of them protrude from the surface and form a microscopic roughness, invisible to the naked eye, that prevents full contact between two layers. The faces touch only at the peaks of those particles, air remains between them and the film separates with minimal force.

Its mechanism is physical. The particles stay in place and the protection exists from the moment the film solidifies, with no waiting time and no dependence on humidity. That characteristic sets it apart from additives that work by migration.

The minerals that create the roughness

Natural diatomaceous earth silica, synthetic silica, talc, calcium carbonate and kaolin are the minerals most widely used as antiblock agents. Each one has its own particle geometry, hardness, effect on clarity and cost. Silica has a refractive index close to that of polyethylene and reduces clarity less, which is why it is chosen for clear films. Talc, with its platy particle, is effective and economical in films where clarity matters less. Calcium carbonate suits pigmented or opaque films. The mineral is chosen with the end use of the film on the table.

Particle size relative to film thickness

A particle that is too small is buried in the film and no longer creates relief. A particle that is too large shows up as a visible speck, weakens a thin film and scratches the rollers. The right size is proportional to the film thickness, and the size distribution must be narrow so that all particles work the same way. Dispersion matters as much as size: an agglomerate of mineral behaves like a giant particle and produces the same defects. This is where masterbatch has the advantage over powdered mineral, because the concentrate arrives with the particles already separated and wetted by the resin.

Clarity versus antiblock, the balance that sets the dose

Every particle that protrudes from the surface scatters part of the light. That is why antiblock increases the haze of the film and reduces its gloss, and the higher the dose, the more noticeable the effect. Removing the antiblock to gain clarity leads to the blocked roll in the opening of this article. The technical answer is to adjust the mineral, the particle size and the dose to keep the layers separated with the lowest possible loss of clarity.

Haze and gloss, what antiblock takes away from appearance

Haze is measured as the percentage of light the film deflects as it passes through, with recognized methods such as ASTM D1003, published by ASTM International, the U.S. technical standards organization. Gloss is measured with a reflectance meter at a defined angle. We recommend measuring both on the film with the antiblock already included and approving the sample with those values, because the clarity the customer approves in a film without additive changes as soon as the formula is complete.

Coextrusion: antiblock only in the outer layers

In coextruded film, blocking depends only on the faces that touch. That is why the antiblock is placed in the outer layers and the core layer is left free of mineral. This way the film keeps its layers separated with less haze and lower concentrate consumption.

The dose depends on the resin, the thickness and the end use

A soft, tacky resin requires more antiblock than a stiff resin. A thin film conforms more easily than a thick one. A bag that is opened on a high-speed automatic line needs more reliable separation than a film that is cut and used by hand. In addition, many polyethylene grades leave the resin producer with antiblock already incorporated, and that content adds to the amount in the concentrate. The resin's technical data sheet, the thickness and the customer's machine set the starting point, and the dosing calculation turns that starting point into kilos per shift.

Interactions that change the effect of antiblock

Silica, because of its porous surface, adsorbs part of the slip agent and other migratory additives, and reduces their effectiveness. When the film contains both, the dose of each one is defined together. Some minerals also change the shade or opacity of a pigmented film, which is why an additive concentrate and the color are approved together in the sample. A very hard mineral also accelerates the wear of rollers and blades on high-output lines.

How to verify that the film no longer sticks

The reference laboratory test is the parallel plate blocking load test, such as the one described in ASTM D3354. Two layers of film are pressed together under a defined weight and temperature for a set time, and then the force required to separate them is measured. The result is compared with the value the application requires.

In the plant, a bundle of bags with weight on top, kept in an oven at the temperature of the hottest warehouse in the supply chain, shows in a few days what the warehouse would show in weeks. Validation ends on your customer's machine, at its actual speed and with film that has already gone through storage.

Antiblock masterbatch at Delta Pigmentos

At Delta Pigmentos we have been manufacturing masterbatch in our own plant for 24 years. Within our additives line we address blocking and slip requirements, and we formulate the antiblock concentrate to suit your polymer and your process, in powder or masterbatch form, as a stand-alone additive or integrated into the color of your film. Before recommending a formula, our Quality Control, Design and Development laboratory reviews with you the resin, the thickness, the clarity your customer requires and the warehouse and machine conditions the film will face.

With that information we propose the mineral, the particle size and the dose. You validate the sample in your own production before committing volume. We produce under ISO 9001-2015 certified procedures and ship nationwide from Santa Anita, Jalisco.

Frequently asked questions

Does antiblock reduce the clarity of the film?

It takes away some clarity and gloss, because the protruding particles scatter light. The loss is controlled with the right mineral, a particle size proportional to the thickness and the minimum dose that keeps the layers separated. In coextruded film, placing the antiblock only in the outer layers reduces the effect even further.

Can I solve blocking with a slip agent alone?

The slip agent lowers friction once the layers have separated and slide over one another. Blocking happens earlier, when the faces adhere at rest, and it is prevented by the roughness that antiblock creates. That is why films for automatic lines carry both additives, each with its own dose.

How much antiblock masterbatch is dosed?

The concentrate's technical data sheet indicates a range, and the figure for your film is defined with the resin, the thickness, the antiblock the polyethylene grade already contains and the demands of your customer's machine. That figure is confirmed with a blocking test under the most demanding warehouse conditions in your supply chain.

Antiblock masterbatch determines whether a film reaches the customer ready to run or stuck on the roll, and its dose is balanced against the clarity the product needs. At Delta Pigmentos we help you define the mineral, the particle size and the dose, with our own laboratory and ISO 9001-2015 certified procedures. Request your quote through WhatsApp or our contact form with your resin, your process, the film thickness and the clarity your customer requires; our laboratory will respond with a technical proposal. Every request is reviewed within the following 24 business hours.

Keep reading

Related articles

Quote

Request a quote with your color reference

We reply with a technical proposal: product, loading and recommended process.